KAD/ADC/113 ¼-bridge ADC (current excitation, PT100 temp. sensors, extended temp., 3 kHz b/w) - 16 channels at 12 ksps
The KAD/ADC/113/ET provides independent excitation for up to 16 channels and is intended for PT100 RTD type sensors. Each channel has a separate programmable digital filter and A/D converter. At the heart of the KAD/ADC/113/ET is a hard-wired state-machine that oversamples all channels at a rate between 48 ksps and 96 ksps and digitally filters any noise above the user-programmable cutoff frequency. This is achieved using cascaded, half-band, Finite-Impulse-Response (FIR) filters followed by an 8th order Butterworth Infinite-Impulse-Response (IIR) filter with a default cutoff point set at one quarter of the sampling frequency (fc = fs / 4). All signals are sampled simultaneously. Thus, when several channels are sampled at different sampling rates, at the start of an acquisition cycle all channels are aligned.
The current through the RTD is programmable from 1 mA to 2 mA in steps of 0.5 µA. The excitation current through the RTD is kept constant. As the resistance changes, the voltage across the RTD (and hence as seen by the amplifier) changes linearly.
A linearization table for each channel can be used to compensate for non-linear sensors or to fine-tune gain and offset.
- REQUEST A QUOTE
- 16 ¼-bridge (3-wire) input channels for PT100 Resistance Temperature Detector (RTD) type sensors
- Simultaneous sampling 16-bit A/D for each channel
- High accuracy (±0.84°C between -60 and 250°C @ 1.6 mA)
- Programmable input range and balance current per channel
- Programmable excitation, per group of 4 channels
- Linear (constant current) operation
- 8th order Butterworth filter with programmable cutoff frequency per channel
- Short to ground on any channel does not affect others
- Up to 12,000 samples per second per channel
- Up to 3 kHz bandwidth
- Operates at extended temperature range of -55 to 105°C
- Temperature measurements with RTD PT100
DAS Studio 3 software allows you to configure DAUs, network switches, recorders and ground stations in an integrated environment. The software is optimized for multi-core platforms with a...
KAD/ADC/135 Full/½-bridge ADC (voltage/current excitation, programmable analog gain, FIR/IIR, 6.25 kHz b/w) - 12 channels at 25 ksps
The KAD/ADC/135 is used to condition and digitize up to 12 differential-ended analog channels. At the heart of the KAD/ADC/135 is a hard-wired state-machine that oversamples all channels at a rate...
KAD/ADC/136 Flexible ADC (full/½-bridge, ICP, PT100, thermocouple, FIR/IIR, 12.5 kHz b/w) - 8 channels at 50 ksps
The KAD/ADC/136 is used to condition and digitize up to eight analog channels. Each channel can be configured for use in differential-ended or single-ended voltage measurement, ICP sensor, RTD...
The KAD/DSI/102 monitors the status (high/low) of up to 24 differential-ended discrete input channels. Each of these has an assigned programmable 32-bit counter. Additionally each of the inputs can...
The KAD/MAT/101 allows you run your own programs based on a dual core C6000DSP+ARM9 microcontroller. It provides high performance DSP functions in a widely used architecture. You can develop...
The KAD/VID/106 is an H.264 video encoder card that converts one of three composite analog video inputs, or one Y/C analog video input to digital video and compresses it. Compressed video bit-rate...
The KAM/CHS/03F is a compact three user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/008 power supply unit. The backplane has three slots for...
The KAM/CHS/04L is a compact four user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/006 power supply unit. The backplane has four slots for...
The NET/REC/001 is a stand-alone Ethernet network recorder. Incoming Ethernet frames are written to a CompactFlash card using a FAT32 file system. The NET/REC/001 can be configured via...
8-port Ethernet switch (Xbar, SNMP, IEEE 1588 V1/V2 Grandmaster) The NET/SWI/101 is a Gigabit Ethernet switch designed for operating in harsh environments. Each port on the NET/SWI/101 is...
Contact our sales team today to learn more about our products and services.
Our support team can help answer your questions - contact us today.