KAD/ADC/114 Full-bridge ADC (voltage excitation, strain gages, 3 kHz b/w) - 16 channels at 12 ksps
The KAD/ADC/114 is used to condition and digitize up to 16 differential-ended analog channels. At the heart of the KAD/ADC/114 is a hard-wired state-machine that oversamples all channels at a rate between 48 ksps and 96 ksps and digitally filters any noise above the user-programmable cutoff frequency.
This is achieved using cascaded, half-band, Finite-Impulse-Response (FIR) filters followed by an 8th order Butterworth Infinite-Impulse-Response (IIR) filter with a default cutoff point set at one quarter of the sampling frequency (fc = fs / 4). All signals are sampled simultaneously. Thus, when several channels are sampled at different sampling rates, at the start of an acquisition cycle all channels are aligned.
Excitation on the KAD/ADC/114 is programmable using four D/A converters, each of which is connected to two pairs of drivers. If more than eight excitations are required, each excitation output can be connected to two bridges.
The KAD/ADC/114 is available with three different input ranges (±10V, ±1V, and ±100mV). The input range must be specified when ordering.
- REQUEST A QUOTE
- 16 full or ½-bridge, potentiometer or differential ended input channels
- Simultaneous sampling 16-bit A/D for each channel
- High accuracy (up to 0.01% FSR typical)
- Programmable input range and balance current per channel
- Eight excitation outputs from four programmable D/A converters
- 8th order Butterworth filter with programmable cutoff frequency per channel
- Short to ground on any channel does not affect others
- Up to 12,000 samples per second per channel
- Up to 3 kHz bandwidth
- Bipolar excitation and balancing before instrumentation amplifier
- Enhanced mechanical strength between motherboard and daughterboard
- High impedance bridge sensors
- Differential voltage measurement
- Strain gage measurement
Setting up data acquisition systems can take a lot of time and effort, particularly as many systems today are growing larger and larger. Managing thousands of channels of data over dozens of data...
KAD/ADC/135 Full/½-bridge ADC (voltage/current excitation, programmable analog gain, FIR/IIR, 6.25 kHz b/w) - 12 channels at 25 ksps
The KAD/ADC/135 is used to condition and digitize up to 12 differential-ended analog channels. At the heart of the KAD/ADC/135 is a hard-wired state-machine that oversamples all channels at a rate...
KAD/ADC/136 Flexible ADC (full/½-bridge, ICP, PT100, thermocouple, FIR/IIR, 12.5 kHz b/w) - 8 channels at 50 ksps
The KAD/ADC/136 is used to condition and digitize up to eight analog channels. Each channel can be configured for use in differential-ended or single-ended voltage measurement, ICP sensor, RTD...
The KAD/DSI/102 monitors the status (high/low) of up to 24 differential-ended discrete input channels. Each of these has an assigned programmable 32-bit counter. Additionally each of the inputs can...
The KAD/MAT/101 allows you run your own programs based on a dual core C6000DSP+ARM9 microcontroller. It provides high performance DSP functions in a widely used architecture. You can develop...
The KAD/VID/106 is an H.264 video encoder card that converts one of three composite analog video inputs, or one Y/C analog video input to digital video and compresses it. Compressed video bit-rate...
The KAM/CHS/03F is a compact three user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/008 power supply unit. The backplane has three slots for...
The KAM/CHS/04L is a compact four user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/006 power supply unit. The backplane has four slots for...
The NET/REC/001 is a stand-alone Ethernet network recorder. Incoming Ethernet frames are written to a CompactFlash card using a FAT32 file system. The NET/REC/001 can be configured via...
The NET/SWI/101 is a Gigabit Ethernet switch designed for operating in harsh environments. Each port on the NET/SWI/101 is full-duplex only and can be set for 10BASE-T, 100BASE-TX, 1000BASE-T link...
Contact our sales team today to learn more about our products and services.
Our support team can help answer your questions - contact us today.