KAD/ADC/117 Full-bridge ADC (current excitation, programmable analog gain, 6 kHz b/w) - 8 channels at 24 ksps
The KAD/ADC/117 has eight channels of signal conditioning and data acquisition for differential voltages, strain gage and bridge measurements. In addition to the measurement channel, the KAD/ADC/117 provides independent constant current excitation for up to eight channels. Each differential ended signal has a separate programmable amplifier, filter and A/D converter.
At the heart of the KAD/ADC/117 is a hard-wired state-machine that over-samples all channels at a rate between 96 ksps and 192 ksps and digitally filters any noise above the user-programmable cutoff frequency. This is achieved using cascaded, half-band, decimate by 2, 15 tap, Finite-Impulse-Response (FIR) filters with 32-bit coefficients followed by 8th order Butterworth (IIR) filter with a default cutoff point set to a quarter of the sampling frequency. All signals are sampled simultaneously. Thus, when several channels are sampled at different sampling rates, at least at the start of an acquisition cycle all channels will be aligned.
The excitation current is programmable (0 mA to 2 0mA in 5 µA steps) and is kept constant. As the resistance changes, the voltage across the bridge (and hence as seen by the amplifier) changes linearly.
- REQUEST A QUOTE
- Eight full bridge or Differential-ended (D/E) input channels
- 16-bit simultaneous sampling on all channels
- High accuracy
- Programmable current excitation and input range per channel
- 8th order Butterworth filter with programmable cutoff frequency per channel
- Linear bridge operation – constant current
- Short to ground on any channel does not affect others
- Up to 24,000 samples per second per channel
- Up to 6 kHz bandwidth
- Bridge applications with long leads/barriers
- General purpose voltage measurement
DAS Studio 3 software allows you to configure DAUs, network switches, recorders and ground stations in an integrated environment. The software is optimized for multi-core platforms with a...
KAD/ADC/135 Full/½-bridge ADC (voltage/current excitation, programmable analog gain, FIR/IIR, 6.25 kHz b/w) - 12 channels at 25 ksps
The KAD/ADC/135 is used to condition and digitize up to 12 differential-ended analog channels. At the heart of the KAD/ADC/135 is a hard-wired state-machine that oversamples all channels at a rate...
KAD/ADC/136 Flexible ADC (full/½-bridge, ICP, PT100, thermocouple, FIR/IIR, 12.5 kHz b/w) - 8 channels at 50 ksps
The KAD/ADC/136 is used to condition and digitize up to eight analog channels. Each channel can be configured for use in differential-ended or single-ended voltage measurement, ICP sensor, RTD...
The KAD/DSI/102 monitors the status (high/low) of up to 24 differential-ended discrete input channels. Each of these has an assigned programmable 32-bit counter. Additionally each of the inputs can...
The KAD/MAT/101 allows you run your own programs based on a dual core C6000DSP+ARM9 microcontroller. It provides high performance DSP functions in a widely used architecture. You can develop...
The KAD/VID/106 is an H.264 video encoder card that converts one of three composite analog video inputs, or one Y/C analog video input to digital video and compresses it. Compressed video bit-rate...
The KAM/CHS/03F is a compact three user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/008 power supply unit. The backplane has three slots for...
The KAM/CHS/04L is a compact four user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/006 power supply unit. The backplane has four slots for...
The NET/REC/001 is a stand-alone Ethernet network recorder. Incoming Ethernet frames are written to a CompactFlash card using a FAT32 file system. The NET/REC/001 can be configured via...
8-port Ethernet switch (Xbar, SNMP, IEEE 1588 V1/V2 Grandmaster) The NET/SWI/101 is a Gigabit Ethernet switch designed for operating in harsh environments. Each port on the NET/SWI/101 is...
Contact our sales team today to learn more about our products and services.
Our support team can help answer your questions - contact us today.