KAD/ADC/126 Accelerometer ADC (current excitation, programmable analog gain, 25 kHz b/w) - 4 channels at 100 ksps
The KAD/ADC/126 is used to condition and digitize up to four Single-ended (S/E) analog channels. All of these channels have a constant current source and high-pass (DC-reject) filter for use with integrated charge-amp piezoelectric (ICP) accelerometer devices.
At the heart of the KAD/ADC/126 is a hard-wired state machine that over-samples all channels at a rate between 200 ksps and 400 ksps and digitally filters any noise above the user-programmable cutoff frequency.
This is achieved using cascaded, half-band, Finite-Impulse-Response (FIR) filters followed by an 8th order Butterworth IIR filter with a default cutoff point set at one quarter of the sampling frequency (fc = fs/4).
All signals are sampled simultaneously (isochronously). Thus, when several channels are sampled at different sampling rates, at the start of an acquisition cycle all channels will be aligned.
- REQUEST A QUOTE
- Four accelerometer input channels with DC-reject
- Constant current source excitation per channel (3.6 mA typical)
- Simultaneous sampling 16-bit A/D for each channel
- Gain error of 0.1% FSR typical at 10 kHz
- Programmable input range per channel
- 8th order Butterworth filter with programmable cutoff frequency per channel
- Up to 100,000 samples per second per channel
- Up to 25 kHz bandwidth
- Enhanced mechanical strength between motherboard and daughterboard
- Accelerometer signal conditioning and digitalization
- Suitable for ICP, Isotron, Piezotron and Deltatron sensors
DAS Studio 3 software allows you to configure DAUs, network switches, recorders and ground stations in an integrated environment. The software is optimized for multi-core platforms with a...
KAD/ADC/135 Full/½-bridge ADC (voltage/current excitation, programmable analog gain, FIR/IIR, 6.25 kHz b/w) - 12 channels at 25 ksps
The KAD/ADC/135 is used to condition and digitize up to 12 differential-ended analog channels. At the heart of the KAD/ADC/135 is a hard-wired state-machine that oversamples all channels at a rate...
KAD/ADC/136 Flexible ADC (full/½-bridge, ICP, PT100, thermocouple, FIR/IIR, 12.5 kHz b/w) - 8 channels at 50 ksps
The KAD/ADC/136 is used to condition and digitize up to eight analog channels. Each channel can be configured for use in differential-ended or single-ended voltage measurement, ICP sensor, RTD...
The KAD/DSI/102 monitors the status (high/low) of up to 24 differential-ended discrete input channels. Each of these has an assigned programmable 32-bit counter. Additionally each of the inputs can...
The KAD/MAT/101 allows you run your own programs based on a dual core C6000DSP+ARM9 microcontroller. It provides high performance DSP functions in a widely used architecture. You can develop...
The KAD/VID/106 is an H.264 video encoder card that converts one of three composite analog video inputs, or one Y/C analog video input to digital video and compresses it. Compressed video bit-rate...
The KAM/CHS/03F is a compact three user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/008 power supply unit. The backplane has three slots for...
The KAM/CHS/04L is a compact four user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/006 power supply unit. The backplane has four slots for...
The NET/REC/001 is a stand-alone Ethernet network recorder. Incoming Ethernet frames are written to a CompactFlash card using a FAT32 file system. The NET/REC/001 can be configured via...
8-port Ethernet switch (Xbar, SNMP, IEEE 1588 V1/V2 Grandmaster) The NET/SWI/101 is a Gigabit Ethernet switch designed for operating in harsh environments. Each port on the NET/SWI/101 is...
Contact our sales team today to learn more about our products and services.
Our support team can help answer your questions - contact us today.