KAD/ADC/135 Full/½-bridge ADC (voltage/current excitation, programmable analog gain, FIR/IIR, 6.25 kHz b/w) - 12 channels at 25 ksps
The KAD/ADC/135 is used to condition and digitize up to 12 differential-ended analog channels. At the heart of the KAD/ADC/135 is a hard-wired state-machine that oversamples all channels at a rate between 100 ksps and 200 ksps and digitally filters any noise above the user-programmable cutoff frequency.
This is achieved using cascaded, half-band, Finite-Impulse-Response (FIR) filters followed by an 8th order Butterworth Infinite-Impulse-Response (IIR) filter with a default cutoff point set at one quarter of the sampling frequency (fc = fs/4). The IIR filter is bypassed in FIR mode with samples output directly from the FIR filter. All signals are sampled simultaneously. When several channels are sampled at different sampling rates, at the start of an acquisition cycle all channels are aligned.
The KAD/ADC/135 supports programmable primary gain, excitation type (current or voltage, with compliance up to 30 mA / ±5.1V), digital filter type as well as completion resistors and high accuracy. Unlike other analog modules, the maximum input voltage range is limited to ±2.5V.
- REQUEST A QUOTE
- 12 full or ½-bridge, potentiometer or differential ended input channels
- Simultaneous sampling 16-bit A/D for each channel
- High accuracy (typically 0.02% FSR)
- Programmable primary gain for each channel
- Programmable input range per channel
- Programmable balance current source per channel
- Programmable classic shunt per channel (100kΩ)
- Programmable current or voltage excitation per group of three channels
- Short-to-ground on any channel does not affect others
- Completion resistors for ½-bridge configuration
- 15-tap FIR Kaiser window or 8th order Butterworth (IIR) filter
- Up to 25 ksps per channel and up to 6.25 kHz bandwidth
- High impedance per channel when powered off
- High impedance bridge sensors
- Differential voltage measurement
- Strain gage measurement
Setting up data acquisition systems can take a lot of time and effort, particularly as many systems today are growing larger and larger. Managing thousands of channels of data over dozens of data...
KAD/ADC/136 Flexible ADC (full/½-bridge, ICP, PT100, thermocouple, FIR/IIR, 12.5 kHz b/w) - 8 channels at 50 ksps
The KAD/ADC/136 is used to condition and digitize up to eight analog channels. Each channel can be configured for use in differential-ended or single-ended voltage measurement, ICP sensor, RTD...
The KAD/DSI/102 monitors the status (high/low) of up to 24 differential-ended discrete input channels. Each of these has an assigned programmable 32-bit counter. Additionally each of the inputs can...
The KAD/MAT/101 allows you run your own programs based on a dual core C6000DSP+ARM9 microcontroller. It provides high performance DSP functions in a widely used architecture. You can develop...
The KAD/VID/106 is an H.264 video encoder card that converts one of three composite analog video inputs, or one Y/C analog video input to digital video and compresses it. Compressed video bit-rate...
The KAM/CHS/13U/ET is a thirteen user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a power supply module which regulates power supplies for the backplane...
The NET/REC/001 is a stand-alone Ethernet network recorder. Incoming Ethernet frames are written to a CompactFlash card using a FAT32 file system. The NET/REC/001 can be configured via...
The NET/SWI/101 is a Gigabit Ethernet switch designed for operating in harsh environments. Each port on the NET/SWI/101 is full-duplex only and can be set for 10BASE-T, 100BASE-TX, 1000BASE-T link...
Contact our sales team today to learn more about our products and services.
Our support team can help answer your questions - contact us today.