KAD/BCU/101 IRIG-106 backplane controller and encoder with dual modulation output
Download Product Sheet register now
The KAD/BCU/101 functions as two modules in one; an encoder and a backplane controller. The encoder is functionally identical to the KAD/ENC/005 and encodes data from any Acra KAM-500 module in an IRIG-106 Chapter 4 PCM stream.
Parameters to be transmitted are stored in pre-defined locations in RAM. Each parameter has a word definition that includes the bits per word, Most Significant Bit (MSB) (sent first or last), and parity. The encoder has differential ended RS-422 outputs for clock and data, along with buffered TTL outputs for NRZ-L and the bit/word/minor-frame/major-frame pulses.
Up to 15 formats (instruction sequences), can be stored at any time. Format selection is via four single-ended discrete (0-5V) input pins on the I/O (Input/Output) connector. As up to 64 chassis can be programmed using a single programming link, there are also six discrete I/O pins to set a chassis number. These six inputs are pulled to ground internally if left open circuit.
- Downloads
- SPECIFICATIONS
- SUPPORT
- REQUEST A QUOTE
Product Downloads
Featured Downloads
Features
- Encoder
- 100% IRIG-106 compliant
- Fully programmable
- Up to 10 PCM codes at up to 20 Mbps
- 5 to 250k words per major frame
- 5 to 32k words per minor frame
- 4 to 64 bits per word, with even, odd or no parity
- Supports any sync word and sub-frame strategy
- ARINC-573/717 compatible output
- Controller
- Stores up to 15 formats
- Supports dynamic format switching
- Can operate as a master or slave chassis in distributed systems
- Supports fast programming
- Supports Cyclical Redundancy Checking (CRC) insertion at the end of minor frames
Applications
- PCM encoding
DAS Studio 3 Setup software for DAUs, network switches, recorders and ground stations
Setting up data acquisition systems can take a lot of time and effort, particularly as many systems today are growing larger and larger. Managing thousands of channels of data over dozens of data...
KAD/ADC/135 Full/½-bridge ADC - 12ch at 25 ksps
The KAD/ADC/135 is used to condition and digitize up to 12 differential ended analog channels using simultaneous sampling 16-bit A/D for each channel. At the heart of the KAD/ADC/135 is a...
KAD/ADC/136 Flexible ADC (full/½-bridge, ICP, PT100, thermocouple, FIR/IIR, 12.5 kHz b/w) - 8 channels at 50 ksps
The KAD/ADC/136 is used to condition and digitize up to eight analog channels. Each channel can be configured for use in differential-ended or single-ended voltage measurement, ICP sensor, RTD...
KAD/BCU/105 Ethernet backplane controller - IENA compatible, extended temperature
The KAD/BCU/105/AB1/ET is a full-duplex 100BASE-TX Ethernet Acra KAM-500 backplane controller, programmer and packet generator. In acquisition mode some or all acquired data is transferred from...
KAD/BCU/140 Ethernet backplane controller - IENA/iNET-X compatible with TFTP programming
The KAD/BCU/140 is a full-duplex Ethernet Acra KAM-500 backplane controller, programmer, and IPv4 packet generator with a link speed of 100BASE-TX. Upon reception of a programming packet, the...
KAD/ETH/102 Ethernet transmission and programming interface module (iNET-X compatible)
The KAD/ETH/102 is a full-duplex, Fast Ethernet (100 Mbps) module that can be used to program an Acra KAM-500 system or transmit data from an Acra KAM-500 system. In acquisition mode, some or all...
KAD/MAT/101 Microcontroller-based module
The KAD/MAT/101 allows you run your own programs based on a dual core C6000DSP+ARM9 microcontroller. It provides high performance DSP functions in a widely used architecture. You can develop...
KAD/VID/106 H.264 video encoder (analog video input) - 1 channel
The KAD/VID/106 is an H.264 video encoder card that converts one of three composite analog video inputs, or one Y/C analog video input to digital video and compresses it. Compressed video bit-rate...
KAM/CHS/03F Acra KAM-500 chassis (base-mounted power supply and housing) - 3 user-slots
The KAM/CHS/03F is a compact three user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/008 power supply unit. The backplane has three slots for...
KAM/CHS/04L Acra KAM-500 chassis, narrow form - 4 user-slots
The KAM/CHS/04L is a compact four user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/006 power supply unit. The backplane has four slots for...
NET/REC/001 Ethernet Network Recorder (CompactFlash)
The NET/REC/001 is a stand-alone Ethernet network recorder. Incoming Ethernet frames are written to a CompactFlash card using a FAT32 file system. The NET/REC/001 can be configured via...
NET/SWI/101 - Gigabit Ethernet Switch
The NET/SWI/101 is a Gigabit Ethernet switch designed for operating in harsh environments. Each port on the NET/SWI/101 is full-duplex only and can be set for 10BASE-T, 100BASE-TX, 1000BASE-T link...
Product Finder
CONTACT SALES
Contact our sales team today to learn more about our products and services.
GET SUPPORT
Our support team can help answer your questions - contact us today.