KAD/BCU/105 Ethernet backplane controller - IENA compatible, extended temperature
The KAD/BCU/105/AB1/ET is a full-duplex 100BASE-TX Ethernet Acra KAM-500 backplane controller, programmer and packet generator.
In acquisition mode some or all acquired data is transferred from the backplane to the onboard CVT. Onboard, it is packetized into a user-defined structure. Once full, the packet is transmitted via UDP.
Any number of user-defined IENA packet structures can be handled simultaneously. Different packet identifiers, packet sizes and destination IP addresses can be individually programmed for each packet type. Destination IP addresses can be unicast, multicast, or broadcast.
Upon reception of a programming packet, the module immediately exits acquisition mode and switches to program/verify mode. In program/verify mode it can read or write data blocks to or from any module within an Acra KAM-500 chassis.
The Acra KAM-500 backplane controller supports chassis programming via Ethernet. Synchronization is achieved using the IEEE 1588 PTP.
The KAD/BCU/105/AB1/ET supports IPv4 networks with fixed IP address allocation, including user-assignment of the module's IP address. The module is factory-programmed with a unique Ethernet MAC address.
- REQUEST A QUOTE
- TEC-NOT-032 - Using Ethernet for data acquisition
- TEC-NOT-049 - Power estimation
- TEC-NOT-053 - Using the KAD/BCU/105
- TEC-NOT-016 - Power dissipation, an example
- Manual: DAS Studio 3 User Manual
- Environmental Qualifications Handbook
- KAM-500 Databook
- KSM-500 Databook
- Aerospace Instrumentation Brochure
- Programming and verification of Acra KAM-500 chassis
- Synchronization with an external IEE 1588 Precision Time Protocol version 1 (PTPv1) source
- Bi-directional, full-duplex, 100BASE-TX Ethernet connection with auto-MDIX
- Static IP address, upper 16 bits permanently set to 172.28; lower 16 bits assigned via top block wiring
- User Datagram Protocol (UDP) support for packets up to 64 kbyte (32 kilosamples) via IP fragmentation
- Current Value Table (CVT) of up to 1 megasample
- IPv4 protocol supported
- Supports Address Resolution Protocol (ARP) and ping
- Operating temperature from -55 to 105°C
- Ethernet based data acquisition systems
Setting up data acquisition systems can take a lot of time and effort, particularly as many systems today are growing larger and larger. Managing thousands of channels of data over dozens of data...
KAD/ADC/135 Full/½-bridge ADC (voltage/current excitation, programmable analog gain, FIR/IIR, 6.25 kHz b/w) - 12 channels at 25 ksps
The KAD/ADC/135 is used to condition and digitize up to 12 differential-ended analog channels. At the heart of the KAD/ADC/135 is a hard-wired state-machine that oversamples all channels at a rate...
KAD/ADC/136 Flexible ADC (full/½-bridge, ICP, PT100, thermocouple, FIR/IIR, 12.5 kHz b/w) - 8 channels at 50 ksps
The KAD/ADC/136 is used to condition and digitize up to eight analog channels. Each channel can be configured for use in differential-ended or single-ended voltage measurement, ICP sensor, RTD...
The KAD/BCU/101 functions as two modules in one; an encoder and a backplane controller. The encoder is functionally identical to the KAD/ENC/005 and encodes data from any Acra KAM-500 module in an...
The KAD/BCU/140 is a full-duplex Ethernet Acra KAM-500 backplane controller, programmer, and IPv4 packet generator with a link speed of 100BASE-TX. Upon reception of a programming packet, the...
The KAD/DSI/102 monitors the status (high/low) of up to 24 differential-ended discrete input channels. Each of these has an assigned programmable 32-bit counter. Additionally each of the inputs can...
The KAD/MAT/101 allows you run your own programs based on a dual core C6000DSP+ARM9 microcontroller. It provides high performance DSP functions in a widely used architecture. You can develop...
The KAD/VID/106 is an H.264 video encoder card that converts one of three composite analog video inputs, or one Y/C analog video input to digital video and compresses it. Compressed video bit-rate...
The KAM/CHS/03F is a compact three user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/008 power supply unit. The backplane has three slots for...
The KAM/CHS/04L is a compact four user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/006 power supply unit. The backplane has four slots for...
The NET/REC/001 is a stand-alone Ethernet network recorder. Incoming Ethernet frames are written to a CompactFlash card using a FAT32 file system. The NET/REC/001 can be configured via...
The NET/SWI/101 is a Gigabit Ethernet switch designed for operating in harsh environments. Each port on the NET/SWI/101 is full-duplex only and can be set for 10BASE-T, 100BASE-TX, 1000BASE-T link...
Contact our sales team today to learn more about our products and services.
Our support team can help answer your questions - contact us today.