KAD/TDC/102 Thermocouple ADC (reference compensation, 250 Hz b/w) - 15 channels at 1 ksps
The KAD/TDC/102 is used to condition and digitize up to fifteen thermocouple channels and three channels of module junction temperature. Each thermocouple channel can be configured separately for use with a wide range of thermocouple types.
Together, the KAD/TDC/102 and the CON/KAD/010 connector use the preconfigured module junction temperature channels 0 and 2, to perform linearization and cold junction compensation for each thermocouple channel. At the heart of the KAD/TDC/102 is a hard-wired state-machine that oversamples all channels at a rate up to 50 ksps and digitally filters any noise above the user-programmable cutoff frequency.
This is achieved using cascaded, half-band, Finite-Impulse-Response (FIR) filters followed by an 8th order Butterworth Infinite-Impulse-Response (IIR) filter with a default cutoff point set at one quarter of the sampling frequency (fc = fs/4). All signals are sampled simultaneously. When several channels are sampled at different sampling rates, at the start of an acquisition cycle, all channels are aligned.
- REQUEST A QUOTE
- 15 thermocouple input channels
- ±0.5°C typical and ±1.5°C worst case accuracy for K-type and L-type thermocouple (-50 to +150°C)
- ±1.0°C typical and ±2.5°C worst case accuracy for K-type and L-type thermocouple (outside -50 to _150°C range)
- Junction block temperature measurement
- Programmable thermocouple type (per module)
- Digital reference junction compensation
- Up to 250 Hz bandwidth
- Up to 1,000 samples per second (sps) per channel
- 8th order Butterworth filter with programmable cutoff frequency per channel
- Supports grounded and isolated thermocouples
- External, third party cold junction blocks with PT100 sensors can be used if required
- Temperature measurements with thermocouples
The KAM/CHS/13U/ET is a thirteen user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a power supply module which regulates power supplies for the backplane...
The NET/SWI/101 is a Gigabit Ethernet switch designed for operating in harsh environments. Each port on the NET/SWI/101 is full-duplex only and can be set for 10BASE-T, 100BASE-TX, 1000BASE-T link...
The KAD/DSI/102 monitors the status (high/low) of up to 24 differential-ended discrete input channels. Each of these has an assigned programmable 32-bit counter. Additionally each of the inputs can...
The KAD/VID/106 is an H.264 video encoder card that converts one of three composite analog video inputs, or one Y/C analog video input to digital video and compresses it. Compressed video bit-rate...
The KAD/MAT/101 allows you run your own programs based on a dual core C6000DSP+ARM9 microcontroller. It provides high performance DSP functions in a widely used architecture. You can develop...
KAD/ADC/136 Flexible ADC (full/½-bridge, ICP, PT100, thermocouple, FIR/IIR, 12.5 kHz b/w) - 8 channels at 50 ksps
The KAD/ADC/136 is used to condition and digitize up to eight analog channels. Each channel can be configured for use in differential-ended or single-ended voltage measurement, ICP sensor, RTD...
KAD/ADC/135 Full/½-bridge ADC (voltage/current excitation, programmable analog gain, FIR/IIR, 6.25 kHz b/w) - 12 channels at 25 ksps
The KAD/ADC/135 is used to condition and digitize up to 12 differential-ended analog channels. At the heart of the KAD/ADC/135 is a hard-wired state-machine that oversamples all channels at a rate...
The KAM/CHS/04L is a compact four user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/006 power supply unit. The backplane has four slots for...
The KAM/CHS/03F is a compact three user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/008 power supply unit. The backplane has three slots for...
The NET/REC/001 is a stand-alone Ethernet network recorder. Incoming Ethernet frames are written to a CompactFlash card using a FAT32 file system. The NET/REC/001 can be configured via...
Contact our sales team today to learn more about our products and services.
Our support team can help answer your questions - contact us today.